MACHINING.TRPrecision Machining. Engineered in Turkey.
  1. Home
  2. Knowledge
  3. Glossary

Knowledge

Machining glossary

Clear definitions of the terms used in CNC machining, tolerancing and inspection.

Allowance
Material deliberately left on a feature for a later operation such as finishing, grinding or heat-treatment distortion.
Annealing
Heat treatment that softens material and relieves stresses, often applied before machining hardenable steels.
Axial depth of cutap
Depth of engagement of a cutter measured along its axis.
Back boring
Machining a counterbore or face on the far side of a hole with a tool that passes through the hole first.
Bar feeder
Device that automatically pushes bar stock through the spindle of a lathe for unattended production.
Bilateral tolerance
Tolerance that allows variation in both directions from the nominal size, e.g. 20 ±0.05.
Blind hole
Hole that does not pass completely through the part.
Boring
Enlarging and truing an existing hole with a single-point tool to achieve accurate size, position and straightness.
Built-up edgeBUE
Workpiece material welded to the cutting edge, which degrades finish and size.
CAM
Computer-aided manufacturing: software that generates tool paths and NC programs from a 3D model.
Chamfer
Bevelled edge that removes a sharp corner, eases assembly or protects threads.
Chip loadfz
Thickness of material removed by each cutting edge; often used informally for feed per tooth.
Chip thinning
Reduction of actual chip thickness when radial engagement is less than half the cutter diameter; compensated by increasing feed.
Climb millingdown milling
Milling in which the cutter rotation and feed direction are the same at the contact point; chips start thick and end thin.
Collet
Slotted sleeve that clamps round, hex or square bar concentrically; common on bar-fed lathes.
Concentricity
Condition in which the median points of a feature lie on a datum axis; often replaced by run-out or position in practice.
Conventional millingup milling
Milling in which cutter rotation opposes the feed direction; chips start thin.
Coordinate measuring machineCMM
Machine that measures geometry by probing points in three dimensions and evaluating them against a datum system.
Counterbore
Flat-bottomed enlargement of a hole that recesses a screw head.
Countersink
Conical enlargement of a hole for flat-head screws or for deburring.
Cutting speedvc
Relative speed between cutting edge and workpiece surface, usually in m/min or SFM.
Cycle time
Time to complete one part, including cutting, tool changes and non-cutting moves.
Datum
Theoretically exact point, axis or plane derived from a datum feature; the reference for geometrical tolerances.
Deburring
Removal of burrs from edges after machining, manually or by programmed tool paths, brushing or tumbling.
Design for manufacturabilityDFM
Designing parts so that they can be produced reliably and economically without compromising function.
Dowel pin
Precision pin used to locate parts relative to one another; requires accurate reamed holes.
Driven toollive tool
Rotating tool on a lathe turret that allows milling and drilling while the part is held in the spindle.
EDM
Electrical discharge machining: removes material by sparks; used for sharp internal corners and hardened materials.
End mill
Rotating cutter with cutting edges on its end and periphery, used for slots, pockets and contours.
Envelope requirement
Rule that a feature of size must not exceed its maximum-material boundary of perfect form; indicated by Ⓔ in ISO.
Face milling
Machining a flat surface with a cutter whose axis is perpendicular to that surface.
Feed per revolutionf
Distance the tool advances per revolution of the spindle, mainly in turning and drilling.
Feed ratevf
Speed of the tool relative to the workpiece along the path, in mm/min or in/min.
First article inspectionFAI
Full documented verification of the first production part against every drawing requirement.
Fixture
Workholding device designed for a specific part to locate and clamp it repeatably.
Flatness
Form tolerance: all points of a surface must lie between two parallel planes a set distance apart.
Fundamental deviation
In ISO 286, the deviation closest to the nominal size; designated by a letter (H, g, k …).
G-code
Common name for the ISO 6983 programming language that controls CNC machine movements.
GD&T
Geometric dimensioning and tolerancing: a symbolic language for form, orientation, location and run-out.
General tolerance
Default tolerance that applies to dimensions without individual tolerances, e.g. ISO 2768-mK.
Guide bushing
Bushing on a Swiss-type lathe that supports the bar right next to the cutting zone.
Hard turning
Turning hardened steel (typically above 45 HRC) with CBN or ceramic tools as an alternative to grinding.
Heat number
Identification of the melt from which material was produced; key for traceability to the mill certificate.
Helix angle
Angle of the cutting edge relative to the tool axis; influences cutting forces and chip evacuation.
Honing
Abrasive finishing process for bores that improves size, roundness and surface texture.
Interference fit
Fit in which the shaft is always larger than the hole, producing a press fit.
IT grade
International tolerance grade in ISO 286; a higher number means a wider tolerance.
Knurling
Forming or cutting a pattern of ridges on a cylindrical surface for grip or press fit.
Least material conditionLMC
State of a feature of size containing the least material: largest hole or smallest shaft.
Machinability
Ease with which a material can be machined, considering tool life, forces, chip form and finish.
Material removal rateMRR / Q
Volume of material removed per unit time, in cm³/min or in³/min.
Maximum material conditionMMC
State of a feature of size containing the most material: smallest hole or largest shaft.
Mill-turn
Machine or process combining turning and milling with C-axis and driven tools in one set-up.
Nose radiusrε
Radius at the tip of a turning insert; affects surface finish and edge strength.
Parting off
Cutting a finished part off the bar with a narrow blade on a lathe.
Peck drilling
Drilling in steps with retracts to break and evacuate chips in deep holes.
PMI
Positive material identification: alloy verification by XRF or OES analysis.
Position tolerance
Location tolerance that defines a zone around the theoretically exact position of a feature.
PPAP
Production part approval process: automotive procedure to demonstrate a process can consistently produce conforming parts.
Probe
Touch sensor in the machine spindle used to set datums or measure features in process.
Radial depth of cutae
Width of engagement of a milling cutter perpendicular to its axis.
Reaming
Finishing a pre-drilled hole with a multi-edge tool for accurate size and finish, e.g. H7.
Roughness averageRa
Arithmetic mean of absolute profile deviations from the mean line.
Run-out
Variation of a surface as the part rotates about a datum axis (circular or total run-out).
Set-up
Preparation of machine, workholding, tools and offsets for a particular part.
Spindle speedn
Rotational speed of the spindle in revolutions per minute.
Statistical process controlSPC
Monitoring a process with measurement data and control charts to detect drift before nonconformity.
Stress relieving
Heat treatment that reduces residual stresses to limit distortion during or after machining.
Swiss-type lathe
Sliding-headstock lathe in which the bar moves through a guide bushing; suited to long, slender, precise parts.
Tap drill
Drill size used before tapping; determines thread engagement.
Thread milling
Producing threads with a rotating cutter following a helical path; flexible and safe in difficult materials.
Through-spindle coolantTSC
High-pressure coolant delivered through the spindle and tool to the cutting edge.
Tool life
Cutting time or number of parts before a tool reaches a defined wear criterion.
Tool path
Programmed route of the tool centre or contact point during machining.
Trochoidal milling
Milling strategy with circular or looping paths and low radial engagement for high material removal with controlled load.
Undercut
Feature not reachable from the main tool direction, requiring special tools, extra set-ups or multi-axis machining.
Wiper insert
Insert with a modified edge geometry that allows higher feed for the same theoretical finish.
Work hardening
Increase of hardness in the surface layer due to plastic deformation, typical for austenitic stainless and nickel alloys.
Work offset
Coordinate system that defines the workpiece zero in the machine, e.g. G54.

Enquiry

Have a drawing to review?

Send your 2D drawing and 3D model with quantities, material and required documents. An engineer reviews manufacturability, tolerances and inspection before quoting.

What to include in your enquiry