Three categories
- Equivalent
- the same standardised alloy registered in another system (e.g. EN AW-7075 and AA 7075). Still check temper, product standard and certificate requirements.
- Comparable
- similar chemistry and use, but composition ranges and mechanical requirements differ (e.g. 1.4404 and AISI 316L). Usually acceptable after review.
- Closest substitute
- nearest practical alternative when no direct counterpart exists (e.g. EN AW-6082 and AA 6061). Requires engineering approval.
Substitution checklist
- Chemical composition limits, including restricted elements (lead, sulphur, boron).
- Mechanical properties in the delivery condition and the relevant section size.
- Heat-treatment response and required hardness.
- Corrosion behaviour in the actual environment.
- Certificate type (EN 10204 3.1 / 3.2) and product standard.
- Customer approval documented before production.
Cross-reference table
| EN / Name | W.-Nr. / EN no. | US (AISI / UNS / ASTM) | Relation | Machinability | Density g/cm³ | Typical use / notes |
|---|---|---|---|---|---|---|
| S235JR Carbon & free-cutting steels | 1.0038 | ASTM A36 | Comparable | B – good | 7.85 | General structural steel for brackets, plates and welded frames. Machines readily but can tear on finishing passes. |
| S355J2 Carbon & free-cutting steels | 1.0577 | ASTM A572 Gr. 50 | Comparable | B – good | 7.85 | Higher-strength structural steel for frames, bases and welded machine structures. |
| C45 / C45E Carbon & free-cutting steels | 1.0503 / 1.1191 | AISI 1045 · UNS G10450 | Comparable | B – good | 7.85 | Medium-carbon steel for shafts, pins and gears; can be flame or induction hardened. |
| 11SMn30 Carbon & free-cutting steels | 1.0715 | AISI 1215 · UNS G12150 | Comparable | A – very good | 7.85 | Free-cutting steel with sulphur for high-volume turned parts; limited weldability and case-hardening response. |
| 11SMnPb30 Carbon & free-cutting steels | 1.0718 | AISI 12L14 · UNS G12144 | Comparable | A – very good | 7.85 | Leaded free-cutting steel with excellent chip breaking. Check RoHS / REACH and customer lead restrictions. |
| 16MnCr5 Alloy & case-hardening steels | 1.7131 | AISI 5115 · UNS G51150 | Comparable | B – good | 7.85 | Case-hardening steel for gears, pins and shafts that need a hard surface and tough core. |
| 20MnCr5 Alloy & case-hardening steels | 1.7147 | AISI 5120 | Closest substitute | B – good | 7.85 | Case-hardening steel for more heavily loaded gears and shafts. US grades differ in Cr/Mn content. |
| 42CrMo4 Alloy & case-hardening steels | 1.7225 | AISI 4140 · UNS G41400 | Comparable | C – moderate | 7.85 | Quenched-and-tempered alloy steel for highly loaded shafts, studs and hydraulic parts. Machinability falls as hardness rises. |
| 34CrNiMo6 Alloy & case-hardening steels | 1.6582 | AISI 4340 · UNS G43400 | Comparable | C – moderate | 7.85 | High-toughness Ni-Cr-Mo steel for heavily stressed shafts, crankshafts and defence components. |
| 100Cr6 Alloy & case-hardening steels | 1.3505 | AISI 52100 · UNS G52986 | Comparable | C – moderate | 7.81 | Through-hardening bearing steel; usually machined soft-annealed, then hardened and ground. |
| X153CrMoV12 Tool steels | 1.2379 | AISI D2 · UNS T30402 | Comparable | D – difficult | 7.7 | High-carbon high-chromium cold-work tool steel. Abrasive carbides — machined annealed, finished by grinding or hard milling. |
| X40CrMoV5-1 Tool steels | 1.2344 | AISI H13 · UNS T20813 | Comparable | C – moderate | 7.8 | Hot-work tool steel for dies, inserts and moulds; often pre-hardened for direct machining. |
| 90MnCrV8 Tool steels | 1.2842 | AISI O2 · UNS T31502 | Comparable | C – moderate | 7.85 | Oil-hardening cold-work tool steel for gauges, punches and wear parts. |
| 40CrMnNiMo8-6-4 Tool steels | 1.2738 | AISI P20 (+Ni) | Closest substitute | C – moderate | 7.85 | Pre-hardened plastic-mould steel (typically ~ 280–325 HB as supplied). P20 variants differ in nickel content. |
| X5CrNi18-10 Stainless steels | 1.4301 | AISI 304 · UNS S30400 | Comparable | C – moderate | 7.9 | Standard austenitic stainless steel. Work-hardens; requires sharp tools and continuous feed. |
| X2CrNi18-9 Stainless steels | 1.4307 | AISI 304L · UNS S30403 | Comparable | C – moderate | 7.9 | Low-carbon 304L for welded assemblies. |
| X8CrNiS18-9 Stainless steels | 1.4305 | AISI 303 · UNS S30300 | Comparable | B – good | 7.9 | Free-machining stainless with sulphur — good for turned parts, lower corrosion resistance and poor weldability. |
| X5CrNiMo17-12-2 Stainless steels | 1.4401 | AISI 316 · UNS S31600 | Comparable | C – moderate | 8 | Mo-alloyed austenitic stainless for chloride and chemical exposure. |
| X2CrNiMo17-12-2 Stainless steels | 1.4404 | AISI 316L · UNS S31603 | Comparable | C – moderate | 8 | Low-carbon 316L; the common choice for pharmaceutical, food and marine parts. |
| X6CrNiMoTi17-12-2 Stainless steels | 1.4571 | AISI 316Ti · UNS S31635 | Comparable | C – moderate | 8 | Ti-stabilised 316 grade, common in Germany for welded process equipment. Titanium carbonitrides increase tool wear. |
| X20Cr13 Stainless steels | 1.4021 | AISI 420 · UNS S42000 | Comparable | B – good | 7.7 | Martensitic stainless for pump shafts and valve parts; hardenable. |
| X17CrNi16-2 Stainless steels | 1.4057 | AISI 431 · UNS S43100 | Comparable | C – moderate | 7.7 | Martensitic Cr-Ni stainless with higher toughness and corrosion resistance than 420; used for shafts and marine fittings. |
| X5CrNiCuNb16-4 Stainless steels | 1.4542 | 17-4PH (630) · UNS S17400 | Comparable | C – moderate | 7.8 | Precipitation-hardening stainless. Usually machined in condition A or H1150 and aged afterwards; ageing causes slight dimensional change. |
| X2CrNiMoN22-5-3 Stainless steels | 1.4462 | 2205 · UNS S32205 / S31803 | Comparable | D – difficult | 7.8 | Duplex stainless with high strength and pitting resistance. Tough to machine: rigid set-ups and lower cutting speeds. |
| EN AW-6061 (AlMg1SiCu) Aluminium alloys | 3.3211 (former) | AA 6061 · UNS A96061 | Equivalent | B – good | 2.7 | Versatile heat-treatable alloy (T6/T651). Good machinability and anodising response. |
| EN AW-6082 (AlSi1MgMn) Aluminium alloys | 3.2315 (former) | AA 6061 / 6351 | Closest substitute | B – good | 2.7 | The standard European structural extrusion alloy; often substituted by 6061 in North America. |
| EN AW-7075 (AlZn5,5MgCu) Aluminium alloys | 3.4365 (former) | AA 7075 · UNS A97075 | Equivalent | B – good | 2.81 | High-strength Al-Zn alloy for aerospace and motorsport. Not weldable by conventional methods. |
| EN AW-2024 (AlCu4Mg1) Aluminium alloys | 3.1355 (former) | AA 2024 · UNS A92024 | Equivalent | B – good | 2.78 | High fatigue strength Al-Cu alloy; poor corrosion resistance unless clad or protected. |
| EN AW-2007 (AlCu4PbMgMn) Aluminium alloys | 3.1645 (former) | AA 2011 | Closest substitute | A – very good | 2.85 | Leaded free-machining aluminium for high-volume turned parts; check lead restrictions. |
| EN AW-5083 (AlMg4,5Mn0,7) Aluminium alloys | 3.3547 (former) | AA 5083 · UNS A95083 | Equivalent | C – moderate | 2.66 | Non-heat-treatable marine alloy. Gummy chips; needs sharp, polished tools. |
| CuZn39Pb3 Copper alloys | CW614N | C38500 | Comparable | A – very good | 8.47 | Leaded free-cutting brass — benchmark for machinability. Lead content may be restricted (RoHS exemptions, drinking-water rules). |
| CuZn40Pb2 Copper alloys | CW617N | C37700 | Comparable | A – very good | 8.43 | Leaded brass for hot stampings and turned fittings. |
| Cu-ETP Copper alloys | CW004A | C11000 | Comparable | D – difficult | 8.93 | High-conductivity copper for busbars and electrical contacts. Soft and gummy; burr control is critical. |
| CuSn8 Copper alloys | CW453K | C52100 | Comparable | C – moderate | 8.8 | Phosphor bronze for bushings, springs and bearing parts. |
| CuAl10Ni5Fe4 Copper alloys | CW307G | C63000 | Comparable | C – moderate | 7.6 | Nickel-aluminium bronze with excellent seawater resistance; used for propeller, pump and valve parts. |
| Ti Grade 2 Titanium | 3.7035 | ASTM B348 Gr. 2 · UNS R50400 | Equivalent | C – moderate | 4.51 | Commercially pure titanium — corrosion resistant and ductile. Low thermal conductivity concentrates heat at the edge. |
| Ti-6Al-4V (Grade 5) Titanium | 3.7165 | ASTM B348 Gr. 5 · UNS R56400 | Equivalent | D – difficult | 4.43 | The most widely used titanium alloy. Needs low cutting speeds, high-pressure coolant and rigid fixturing. |
| NiCr22Mo9Nb (Alloy 625) Nickel alloys | 2.4856 | UNS N06625 | Equivalent | D – difficult | 8.44 | Ni-Cr-Mo superalloy for corrosive and high-temperature service. Severe work hardening. |
| NiCr19NbMo (Alloy 718) Nickel alloys | 2.4668 | UNS N07718 | Equivalent | D – difficult | 8.19 | Precipitation-hardening superalloy for turbine and oil-and-gas parts; usually machined solution-annealed or aged depending on the drawing. |
| NiCu30Fe (Alloy 400) Nickel alloys | 2.4360 | UNS N04400 | Equivalent | C – moderate | 8.8 | Ni-Cu alloy with excellent seawater resistance; gummy, prone to built-up edge. |
| EN-GJL-250 Cast irons | EN-JL1040 | ASTM A48 Class 35/40 | Comparable | A – very good | 7.2 | Grey cast iron for housings and machine bases; short chips, abrasive, dust extraction recommended. |
| EN-GJS-400-15 Cast irons | EN-JS1030 | ASTM A536 60-40-18 | Comparable | B – good | 7.1 | Ductile (nodular) iron for housings, hubs and brackets. |
| EN-GJS-700-2 Cast irons | EN-JS1070 | ASTM A536 100-70-03 | Comparable | C – moderate | 7.2 | High-strength pearlitic ductile iron for gears and heavily loaded parts. |
| POM-C (acetal copolymer) Engineering plastics | — | — | — | A – very good | 1.41 | Dimensionally stable acetal for bushings, gears and fixtures; easy to machine to tight tolerances. |
| POM-H (acetal homopolymer) Engineering plastics | — | — | — | A – very good | 1.42 | Acetal homopolymer with slightly higher strength and stiffness; may show centreline porosity in thick stock. |
| PA 6 / PA 66 Engineering plastics | — | — | — | B – good | 1.14 | Tough polyamides for wear parts and rollers. Absorb moisture — allow for dimensional change. |
| PET (semi-crystalline) Engineering plastics | — | — | — | A – very good | 1.39 | Semi-crystalline PET with low moisture uptake and good dimensional stability. |
| PEEK Engineering plastics | — | — | — | B – good | 1.3 | High-performance polymer for high temperatures and chemical exposure; also medical grades. Anneal for tight tolerances. |
| PTFE Engineering plastics | — | — | — | C – moderate | 2.17 | Very low friction and chemical resistance; soft, creeps and has high thermal expansion. |
| PE-UHMW Engineering plastics | — | — | — | C – moderate | 0.93 | Wear-resistant, low-friction polyethylene for guides and food conveyor parts; high thermal expansion. |
Responsibility
This table supports engineering judgement; it does not replace it. Any material substitution is proposed in writing and implemented only with the customer's approval.
